Skip to content
CUCAMONGA PEAK PLUMBING Get prices
Call (840) 201-4829

Costs ยท Rancho Cucamonga

Plumber faucet installation cost in Rancho Cucamonga, with disposal prices

Published ranges for faucet and garbage disposal installs, plus shower repair, and the things that push a quote up or down. National figures, shown as a guide.

Get prices

Published price ranges as horizontal bars for faucet, shower and disposal installs.

Two published guides give the broad numbers. One puts a plumber-installed faucet at $300 to $800 with materials included, and the other puts a new garbage disposal, bought and fitted, at $150 to $950. Your spot inside those ranges is decided by the fixture, the state of the plumbing beneath your sink, and the elbow room in the cabinet. The disposal repair and installation page covers the job itself, and the quote request gets you a written figure for your own house.

How much does faucet installation by a plumber cost?

One guide says $300 to $800 including labor and the faucet, with a kitchen faucet replacement at $400 to $900. Hourly plumber rates in the same guide run $75 to $150 for most work, averaging $90, and a basic swap tends to need one or two hours. What you pick off the shelf tends to swing the total harder than the hours do.

Three sink-deck layouts: single hole, three-hole widespread and a pull-down sprayer.

A plain bathroom faucet sits near the bottom of that band. Expect a higher figure for a pull-down sprayer in the kitchen or a three-hole widespread set in the bathroom. Supplying your own faucet takes its price out of the bill and leaves labor, which is the part a plumber can quote most precisely.

Job Published range Source
Faucet installed, materials included $300 to $800 Fixr
Kitchen faucet replacement $400 to $900 Fixr
Leaky shower faucet fixed $75 to $200 Fixr
Shower repair, general $100 to $600 Fixr

That table is a guide from one national source. What you actually pay is fixed by a local plumber's written quote.

What is the price of installing a garbage disposal?

The This Old House guide gives $150 to $950 for a unit installed, with $400 to $500 as the typical result and about $450 as the average. Doing a faucet and disposal as a pair is listed at $410 to $1,300. The unit itself ranges from roughly $75 for a small continuous-feed model to $1,000 for a 2 horsepower one.

Installation labor runs one to four hours, and plumber labor tops out near $150 an hour. A first disposal in a sink that never had one costs more than a straight swap, because the sink may need a drain change and a switched power source. Adding wiring brings in an electrician, whose time the guide prices at $50 to $120 hourly.

Repair is cheaper than either. The same guide lists $50 to $400, though it adds that a unit near ten years old is usually better replaced than repaired. The quote written for your own sink is still the figure that counts.

What makes quotes for one fixture so far apart?

Six things move the number the most: the fixture's own price, access under the sink, old or stuck shutoff valves, whether wiring is needed, a sink or countertop swap, and the time of the visit. Add a tight cabinet or a corroded valve and a one-hour swap becomes a three-hour afternoon.

  • The fixture. Motor size for disposals, finish and features for faucets.
  • Access. Double-bowl sinks and tight cabinets slow everything.
  • Old shutoffs. If the shutoff stops in the cabinet will not turn, the plumber replaces them or works with the house valve closed. Older Cucamonga and Upland homes are likelier to have original valves, though that depends on whether they were updated.
  • Wiring. A hardwired disposal or a missing switch means electrical work.
  • Sink swap. The disposal guide adds about $400 plus the sink itself when the whole sink changes.
  • Visit timing. Fixr lists a flat emergency call-out of $200 to $300 and a $150 hourly emergency rate, so an after-hours visit costs more than a normal one.

Local water plays a smaller part. The water district's FAQ calls its supply moderately hard to hard, and mineral scale can seize aerators, cartridges and old compression valves. A stuck part adds labor, and a plumber who finds one tells you before charging for the extra time.

Why is shower repair priced differently?

Yes, because the work is inside a wall. Fixr lists a leaking shower faucet at $75 to $200 and shower repair generally at $100 to $600. A dripping head is quick work. A cartridge or valve behind tile costs more, while a stain showing on a ceiling or wall points to a separate leak diagnosis.

If your shower leaks, read how a shower leak plumber traces the source. One dripping spout alone belongs with fixing a leaky faucet.

Getting to the valve may mean opening the wall, which can bring tile or drywall repair. Check if the quote covers closing up the wall or only reaching the leak.

Is it cheaper to do the installation yourself?

Sometimes, for a straightforward faucet. A homeowner who has a replacement kit and basic tools can fit a faucet in an afternoon, and video tutorials for many brands, Moen and GE disposals included, make a decent guide. Where it goes wrong is a seized valve, a leaking supply line, or wiring a hardwired disposal.

Be honest about what you save. On a faucet swap labor is the minor cost, so what you keep is a short stretch of plumber time. Weigh that against a leak inside the cabinet, which can cost much more than the labor you skipped.

Disposals add a safety note. Mains-powered wiring should be done carefully with the breaker off, and gaskets, flanges and mounting rings differ by maker, so work from your own model's manual, not a video about another brand. If anything about the electrical side makes you hesitate, stop and hire the work out.

The contractor-license trigger is a job totaling $1,000 with parts included, or any job with a permit. A routine faucet or disposal install typically stays beneath it.

How do you compare written quotes fairly?

Line the quotes up and read five items on each: the fixture and who buys it, hours or a flat fee, the trip charge, extras like supply lines and valves, and exclusions. A cheap quote that omits parts is not actually cheaper. Ask for every quote in writing, in the same format.

A checklist that helps:

  • Is the fixture named by brand and model, or just "faucet"?
  • Does the price include new supply lines and a shutoff valve if yours is stuck?
  • Is there a separate trip charge? Fixr lists service call fees from $50 to $300.
  • Is the wiring, if any, included or separate?
  • Should a second fault appear, who approves the added cost?
  • Is a deposit asked? Deposits are normally capped under California law at 10 percent of the job or $1,000, whichever comes first. Verify with the CSLB before paying.

For a broader sense of rates, see the plumber hourly rate guide and the overview of what a plumber costs. For other plumbing jobs, start at the home page.

All these ranges are national and published, so treat the plumber's written quote for your home as the real number.

Arrange a plumber visit and quote

Fill this in and we'll arrange a local plumber specialist to come and price the job.

So the business can look at the job and price it.

We earn a referral fee from the plumber who takes your job. You pay us nothing.

Common questions

What would a kitchen faucet swap cost?

One guide shows $400 to $900 to replace a kitchen faucet, against $300 to $800 for a faucet fitted with materials counted. The faucet itself is the bigger cost, labor the smaller. Pull-down models and jobs needing a new valve end up higher, so insist the quote names the fixture.

What does an average disposal installation come to?

The This Old House guide gives about $450 as the average, a typical $400 to $500, and a full range of $150 to $950. That covers the unit and labor. A first-time install, extra wiring or a sink swap can push it past the range, so ask what is included before saying yes.

Does hardwiring a disposal add to the bill?

Possibly. A plug-in unit needs only an outlet, while a hardwired one connects to the circuit, and an electrician may be needed. Electrician time is listed in the disposal guide at $50 to $120 hourly. Ask whether wiring is in the quote or priced separately, and whether the plumber does it.

Can both jobs happen on a single appointment?

Yes, and it saves a trip fee. The disposal guide lists a faucet and disposal together at $410 to $1,300. Mention both in your request, with photos of the sink and cabinet, so the plumber brings parts and allows enough time for the two jobs.

Will the plumber look at a shower fault too?

Often, yes. Fixr lists fixing a leaky shower faucet at $75 to $200 and shower repair at $100 to $600. Mention the shower in your request and describe the symptom: drip from the head, weak flow, or stains below. The plumber can then plan time and parts for both.

Sources used

Updated